6/9/2023 0 Comments Vpn server configurator mac![]() With the L2TP-with-IPsec server enabled/configured on RV260/RV34X, you should note thatġ. Try it out and i hope it works for you too You can connect multiple macos clients concurrently to this vpn server using just PSK. I have checked by connecting from Mac-clients that are behind a NAT-router too.so NAT-T also works perfectly with the above configs on server and the clients. The above configs have been tested by me with 2 mac-clients on a RV345-router. If the C2S-server on RV34X/RV260 is ready, then you may click on connect on this mac-os/ipad/ios client Step-5: you are done (and save the config). ![]() Note: This FQDN/dns-name should-be/MUST-be resolvable by the dns-server configured on the mac-client to the public-ipaddress of the wan-interface of RV34X/RV260ī) For "Remote-ID" enter the value "" (enter without the quotes)Ĭ) For "Local-ID" keep the value empty, do not edit or enter any value here For PSK-based IKEv2-auth, Select the “Secret” and enter the Pre-Shared-Key e.g: Test$123456789Ī) Enter the "Server Address" as dns-name of the RV34X/RV260 Router's wan-ipaddress - say for e.g "" Select “None” only, and do not select certificate (or Use-Certificate) Step-3: In page that is displayed, click first on “Authentication Settings” Step-1: On the desktop of Mac-client.click on the wifi-icon.and Go to “Open Network Preferences” IKEv2 with PSK configuration on MacOS/iOS clients Step-4: Click on Apply and do a permanent save tooĢ. It should be Dynamic IP only as multiple clients will be connecting to this serverĭns/wins/default-domain/etc: to be configured as per the user requirements Note: DO NOT ENABLE/SELECT EXTENDED AUTHENTICATION Note: This wildcard */asterix-star is required, to support multiple mac-ios clients to connect to this vpn-server using psk-authĮxtended Authentication: DISABLE/UNCHECKED enter * (star/asterix) as the wildcard value here. Tunnel Name: Ikev2_MaciOSClients_wPSKonly add and configure a C2S vpn server as below: Phase-2: ESP AES256-SHA256 pfs=no lifetime:3600sec Step-1: In the Ipsec-Profiles, configure the below ipsec-algo-profile used by Mac-iOS clients Configure the C2S server on RV34X/RV260 as below: RV260/RV34X C2S IKEv2 VPN Server for MacOS-iOS Clients using PSK-auth only If you want to establish Client-to-Site IKEv2 tunnels to RV34X/RV260/RV160 routers from multiple MacOS_iOS_Ipad clients using PSK for IKEv2-Auth, then please find below the steps/procedures and info to configure the same on RV34X/RV260/RV160 (C2S config) and on the MacOS/iOS-Ipad clients using IKEv2-PSK-auth only (meaning there is NO username/passwd/useraccounts required for the clients)ġ. Mon Aug 23 13:05:47 2021 : L2TP connecting to server '' (2**.1**.1**.1**).ĭoes anyone have a VPN-setup on RV260 working for macOS clients and does not mind to share the config?Īny help much appreciated. Mon Aug 23 13:05:47 2021 : L2TP IPSec aggressive mode retry with DH group 2 Mon Aug 23 13:05:47 2021 : IPSec connection failed Mon Aug 23 13:05:47 2021 : IPSec phase 1 client started Mon Aug 23 13:05:47 2021 : IPSec connection started The log on the RV260 is of little use here. Here is an excerpt from the log on macOS. I desperately need to find the matching settings here. On macOS, there is not much to configure in the native VPN-client. I have tried so many different settings on the RV260, but none seem to match the settings on macOS. However, I have the requirement to use L2TP/IPSec or CiscoIPSec for the VPN-tunnel, but here I am lost. ![]() So the RV260 is reachable from the internet-side of things. I also managed to get OpenVPN to work and connect to the same internal website, after removing the port-forwarding rule. I was able to access the website running on that internal macOS-client via the public-ip of the RV260. To verify this, I configured port-forwarding for http-traffic to another macOS client behind the router. The RV260 has a public ip-address and is reachable over the internet. Today I spent the whole day and tried to get a macOS client (built-in native VPN-client) connect to my brand-new RV260 via VPN.
0 Comments
Leave a Reply. |